5.6 Automatic watering device

Test Code

#include <Wire.h> 
#include <LiquidCrystal_I2C.h>
LiquidCrystal_I2C lcd(0x27,16,2);  // set the LCD address to 0x27 for a 16 chars and 2 line display
#define soilPin1 A0
#define soilPin2 A1
#define soilPin3 A2
#define soilPin4 A3
#define IN1 3
#define IN2 5
#define IN3 6
#define IN4 9

int count, count_flag;

void setup()
{
  lcd.init();                      // initialize the lcd 
  lcd.init();
  // Print a message to the LCD.
  lcd.backlight();
}


void loop()
{
  pinMode(IN1, OUTPUT);
  pinMode(IN2, OUTPUT);
  pinMode(IN3, OUTPUT);
  pinMode(IN4, OUTPUT);
  int val1 = analogRead(soilPin1);
  int val2 = analogRead(soilPin2);
  int val3 = analogRead(soilPin3);
  int val4 = analogRead(soilPin4);
  lcd.setCursor(0,0);
  lcd.print("S1:");
  lcd.setCursor(3,0);
  lcd.print(val1);
  lcd.setCursor(7,0);
  lcd.print(" ");
  lcd.setCursor(9,0);
  lcd.print("S2:");
  lcd.setCursor(12,0);
  lcd.print(val2);

  lcd.setCursor(0,1);
  lcd.print("S3:");
  lcd.setCursor(3,1);
  lcd.print(val3);
  lcd.setCursor(7,1);
  lcd.print(" ");
  lcd.setCursor(9,1);
  lcd.print("S4:");
  lcd.setCursor(12,1);
  lcd.print(val4);
  delay(200);
  count = count + 1;
  if(count >= 50)  //After 10 seconds, turn off the lCD1602 backlight
  {
    count = 50;
    lcd.noBacklight();
  }
  if(val1 > 590){
    lcd.backlight();
    count = 0;
    digitalWrite(IN1, HIGH);  // Water pump 1
    delay(3000);              //Pumping time is 3 seconds
    digitalWrite(IN1, LOW);   // Shut down the pump
    delay(5000);              //Water penetration time 5 seconds
  }else{
    digitalWrite(IN1, LOW);
  }
  if(val2 > 590){
    lcd.backlight();
    count = 0;
    digitalWrite(IN2, HIGH);
    delay(3000);
    digitalWrite(IN2, LOW);
    delay(5000);
  }else{
    digitalWrite(IN2, LOW);
  }
  if(val3 > 590){
    lcd.backlight();
    count = 0;
    digitalWrite(IN3, HIGH);
    delay(3000);
    digitalWrite(IN3, LOW);
    delay(5000);
  }else{
    digitalWrite(IN3, LOW);
  }
  if(val4 > 590){
    lcd.backlight();
    count = 0;
    digitalWrite(IN4, HIGH);
    delay(3000);
    digitalWrite(IN4, LOW);
    delay(5000);
  }else{
    digitalWrite(IN4, LOW);
  }
}

Test Result：

Insert four soil moisture sensors into four plant pots, and put four water pump pipes in the pots. You can see that the LCD1602 display show soil moisture value. If soil is humid enough, the backlight of the LCD1602 display will be turned off after 10 seconds, which can save power. If soil lacks water, the backlight will light up, and water pumps will pump water to pots. After 3 seconds, the relay will be turned off, the water pump will stop pumping, and wait for 5 seconds, then the soil humidity sensor will continue to detect.